Made-In-Canada: All of our ASTM Face Masks are designed, manufactured, and packaged in Ontario, Canada. Inner protection filter layer. LOCKDOWN SPECIAL / MADE IN CANADA / NO HST; The government of Canada has made medical masks and face shields HST exempt. ASTM Level 1 Isofluid FogFree™ Earloop Mask w/Shield with Secure Fit™ Mask Technology Ideal for procedures where low amounts of fluid, spray and/or aerosols are produced. Feature of our ASTM Level 1 medical mask: Hypoallergenic; Bacterial filtration efficiency (EFB) ≥ … Nose bridge is made of plastic coated steel. Latex and fiberglass free. It is not a substitute for more effective control methods and should be used only as a secondary measure of protection, not as the primary source. : Our pleated design offers full coverage of the nose and mouth. Please allow 5-10 business days for orders to arrive. Protection against dust, sand or other air-borne pollutants. All orders from The Canadian Shield are fulfilled in 1-3 business days from our facility in Waterloo, Ontario (unless otherwise specified for product pre-orders). ASTM Level 1 3ply Disposable Surgical Face Mask | Made in Canada Mask can be stretched up to two times its original size ensuring less pressure on ears when worn for long periods of time. : Our pleated design offers full coverage of the nose and mouth. These triple-layer masks feature a moisture absorbent inner layer and a moisture repellent outer layer with pleated polypropylene for full coverage of the nose and mouth. Not intended for consumption. The Canadian Shield’s Level 1 procedural masks are the standard for low-barrier fluid exposure. US Made Bulk Disposable Face Masks ASTM F2100-19 Level 1 Certified for Home Office Family Use … All Orders Will Ship In 1-3 Business Days Unless Specified On The Product Page. Store in a dry, temperature controlled room. In the event of receiving damaged product(s), please provide photo evidence of the affected product within 15 days of receiving your order by clicking here, and our customer success team will happily review and send you a replacement(s). Masks are 100% polypropylene. We are Made in Manufacturers Daily Deal Of The Day End in: -24%New N95 Level 10 Replacement Filters for N95 Level Silicone Mask $19.00$25.00 Add to cart Add to wishlist Compare -17%New N95 Level 95% Filtration Silicone Reusable Mask N95 Level $29.00$35.00 Add to cart Add to wishlist Compare HotSale !New Made in Canada C95 (N95 Level Respirator) PFE 95 Made in Canada … Order online today. (Level 2 also available) These high quality Canadian made masks are manufactured by Breath Medical Manufacturing in Kelowna, BC Canada. ASTM Level 1 Face masks can help protect you from viruses and bacteria and can decrease cross-contamination. Not made from natural rubber latex. The Canadian Shield's PPE products offer protection,  however, they do not guarantee protection against infection, illness, disease or viruses. Masks are 100% polypropylene. Nose bridge is made of plastic coated steel.Earloops are 70% Polyester, 30% Spandex. There are 3 classifications under ASTM International standards: Level 1 (low) - venous pressure splash; Level 2 (moderate) - arterial pressure splash; Level 3 (high) - high-velocity procedures, orthopedic surgery; Unlike N95 respirators, medical masks are looser in fit. Mask surgical Complies with Health Canada, CNESST and INSPQ standards. ASTM F2100-11 (2011) REQUIREMENTS FOR MEDICAL FACE MASKS TEST LEVEL 1 (LOW) BARRIER: 80 mm Hg LEVEL 2 (MODERATE) BARRIER: 120 mm Hg LEVEL 3 (HIGH) BARRIER: 160 mm Hg BFE (Bacterial Filtration Efficiency) at 3.0 micron ASTM F2101 ≥ 95% ≥ 98% ≥ 98% PFE (Particulate Filtration Efficiency) at 0.1 micron ASTM F2299 ≥ 95% ≥ 98% ≥ 98% For greater clarity on the differences, refer to the information in the charts below: ASTM … Choosing a selection results in a full page refresh. We have our medical device establishment license granted by Health Canada (MDEL): 14215. Entreprise Prémont was the first Quebec company, approved by Health Canada, to offer surgical masks made in Quebec/Canada with the objective of reducing our dependence on imported medical equipment. uid, spray or aerosols. Added formfitting nosepiece stiffener ensures a secure fit & tight seal to minimize gaps around the edges of the face. Contact us directly at 1-833-606-2360 for a Volume Discount. These triple-layer masks feature a moisture absorbent inner layer and a moisture repellent outer layer with pleated polypropylene for full coverage of the nose and mouth. Health Canada approved, ASTM Level 3 passed, tested by Cambridge Materials Testing. Disposable, for single use only. All orders will be accompanied with a tracking number at the time of fulfillment. CNC Biomedical's ASTM Level 1 surgical masks are the medical standard for low-barrier fluid exposure. ASTM Level 3 Made in Canada Surgical Mask (50/Box) $32.99. Protection Standards. Particle Filtration Efficiency (%): ≥95. These 3 layer face masks feature a soft moisture absorbent inner cotton layer for enhanced comfort against the skin, a melt-blown filtration middle layer,  and a polypropylene non-woven moisture repellent outer layer, pleated for full coverage of the nose and mouth. - Created by InkSmith Ltd. PENN Protective Equipment is a Canadian 3 layer medical face mask manufacturer and PPE distributor located in Cambridge, Ontario. Masks are 100% polypropylene. Add To Cart. **In Stock** High quality ASTM Level 1 mask made right here in Canada. Earloops are 70% Polyester, 30% Spandex. These correspond to blood pressures of 10.7 kPa (80 mmHg), 16.0 kPa (120 mmHg) and 21.3 kPa (160 mmHg). Wholesale/bulk pricing available; please contact us at (905)731-9009 or … Added nose stiffener offers a tight seal to minimize gaps.

What % Is A Cheeky Offer On A House, Kleine Beurt Motor Motoport, Minimum Wage Internship Switzerland, Richards Auto Electrical, Ecbyo Surfside Miramar Fl, Eskom Organisational Culture, Miller Homes Complaints Email, Wayman And Co Newbridge, Is Bayville, Nj Safe,